Open sidebar

Equipment - TECHNONICOL

A roofing burner, a gas-jet or a liquid-fuel burner are used in order to warm up the amount of fused roofing material, to prepare flooring underlay, to prepare the base of the roof (to dry and to warm up) during installation of a waterproofing layer and during other repair and building works that are connected with the use of free flame for warming up the surface till 400°С.

Air torches GG-2, GG-2u, GG-2с, GGK1, Sievert have a cocking piece for managing the flame, and it gives an opportunity to change quickly economical standby mode into working one and backwards.

The burners are produced from strong non-corrosive materials or from materials with a special zinc coating. The construction of the sleeve protects the flame from the wind. Every burner is packed in a convenient corrugated box. In every box there is an additional set of rubber rings for the cocking piece.

It is advisable to use air torches together with propane reducer BPO-5-3. The reducer is used to optimize gas flow in propane cylinder, to control the pressure at the outlet of the cylinder and to provide stable gas flow in the burner. With the use of the reducer the economy of propane-butane mixture can be up to 30%.

Liquid-fluid burners GRJ have a valve device. Diesel oil is used as an inflammable. The burners are produced from strong non-corrosive materials. The flame of the burner is well protected from the wind. While using diesel oil outdoors the temperature of the air shouldn’t be lower than 15°С below zero.

You can get detailed information about the patterns and their availability from a sales representative of a trade unit.

Materials ROOFING EQUIPMENT:



 

This section presents information on equipment that helps to extend the working life of waterproof carpets.

The stable plastic aerators are designed for use in different climate zones.

The rainwater funnels with a filter against leaves are designed to remove rainwater from the surface of flat roofs.

The open flame burners of different kinds are used during waterproofing works to heat up a cover mass of a roofing melting material, to prepare floors and roofings (drying and heating-up). The burners are also used for other types of repair and construction works, technologically connected with the use of open flame.


 

Where to buy? Who can install?
Trusted solutions for your construction needs. TechnoNICOL Systems.
 

A traditional flat roof consists of the base, which is covered with a waterproof carpet made of bitumen-based roll materials in order to protect from effects of precipitations.

Because of the fact that it is almost impossible to provide perfect impermeability of the vapour-barrier, vapour from rooms and surrounding areas gets under the waterproofing layer and condenses in there. A tight waterproof carpet does not let moisture evaporate into the surrounding area and after some time a lot of water gathers in the waterproofing layer. It streams down, causing wet spots on the ceiling, at a negative temperature it gets frozen, expands and tears waterproofing layer. If water gets into heat-insulating layer, heat insulation gets frozen during the frost and loses its insulating properties. That’s why heating expenses increase. In a warm season constructions get covered with mould.

A successful solution of this problem is aerators for flat roofs.

Plastic aerators (roof cowls) with different diameters are used by installation of “breathing” roofs and by readjustment of a roof. They are used for abstraction of vapour. They protect a roofing carpet from swelling. They prolong the life time of the waterproofing layer. Plastic aerators do not corrode and can be used in various climatic zones. On flat roofs with simple configuration aerators are placed evenly in the whole area of the roof in the highest places of the roofing carpet and in places of juncture of heat-insulating mats.

Check whether such devices are installed on your roof. Perhaps, numerous repairs of your roof are connected with the absence of aerators. You can get detailed information about the patterns and their availability from a sales representative of a trade unit.

Materials AERATORS FOR FLAT ROOFS:



 

This section presents information on equipment that helps to extend the working life of waterproof carpets.

The stable plastic aerators are designed for use in different climate zones.

The rainwater funnels with a filter against leaves are designed to remove rainwater from the surface of flat roofs.

The open flame burners of different kinds are used during waterproofing works to heat up a cover mass of a roofing melting material, to prepare floors and roofings (drying and heating-up). The burners are also used for other types of repair and construction works, technologically connected with the use of open flame.


 

Where to buy? Who can install?
Trusted solutions for your construction needs. TechnoNICOL Systems.
 

Rainwater heads with a filter protecting from leaves. They are used for abstraction of rainwater from the surface of flat roofs. As you install them you should fix it in addition to the base. During installation a part of the head is fused between two layers of bitumen-polymer material.

There are some modifications with heating that prevents drain hole form freezing during the time between seasons (autumn – winter – spring).

The amount of rainwater heads needed for one roof depends on the architecture and application conditions of the roof and on the amount of precipitations in this area. On average one rainwater head is placed on every 300-400 square meters, but there should not be less than one head on a roof.

You can get detailed information about the patterns and their availability from a sales representative of a trade unit.

Materials RAINWATER HEADS:



 

This section presents information on equipment that helps to extend the working life of waterproof carpets.

The stable plastic aerators are designed for use in different climate zones.

The rainwater funnels with a filter against leaves are designed to remove rainwater from the surface of flat roofs.

The open flame burners of different kinds are used during waterproofing works to heat up a cover mass of a roofing melting material, to prepare floors and roofings (drying and heating-up). The burners are also used for other types of repair and construction works, technologically connected with the use of open flame.


 

Where to buy? Who can install?
Trusted solutions for your construction needs. TechnoNICOL Systems.
 

NOTIFICATION: We inform you that the site processes personal data and uses "cookies". We undertake to ensure the confidentiality of personal data received from you for the purposes specified in this Privacy Policy on personal data processing, as well as safety when processing them in accordance with the requirements of the Legislation of the Russian Federation. To confirm your consent to processing data on the above conditions, click "I agree"